If the non woven machine malfunctions while in operation, what should you do? Today, we'll provide you a few ideas on how to deal with this issue. There are a variety of nonwoven machinery options, such as nonwoven bag producing machines, carding machines, and mask machines. The following is a breakdown of the problems that might arise while using certain pieces of equipment, as well as the causes and remedies for each one. I'm hoping to be of assistance to you.
A machine for making nonwoven bags SUNTECH
The substance is not dragged by the stepper motor.
- Verify that the voltage coming from the power source is normal. To safeguard the servo amplifier, the power supply has to be at a safe level
- Check to see whether the servo amplifier's fuse has been tampered with or blown.
No matter how hard you try, the servo amplifier plug may not be firmly inserted.
Verify whether or not the microcomputer's Hall signal is normal
Drag time that is either excessively lengthy or excessively short
Check to see whether the synchronous belt connecting the stepper motor to the driving rubber roller is loose.
- Verify that the driving rubber roller pressure is enough.
Determine whether the discharge is excessively heavy or out of rhythm with the host.
The drag is out of synchronization with the host. ‘
No matter what, check to see whether the Hall signal magnet has moved.
Second, check to see whether the Hall switch is malfunctioning.
When feeding and receiving, check to see whether the feeding and receiving speed control board is damaged.
There are a few things you can do to make sure the speed control board fuse isn't broken:
The carbon brush on the motor is not properly engaged.
- The speed controlling potentiometer has been destroyed or the contact has been slammed shut.
There is a problem with the electric heater's heating or temperature-control mechanisms
In one of the following ways:
- The contact between the thermocouple and the sensor is poor.
- Failure of a triac or solid state relay
The computer has been jolted awake.
Electrostatic scavenger interference
Too high or too low a voltage in the power supply
- The feeding motor is either too sluggish or too rapid.
It's impossible to verify the accuracy of
The light eye's sensitivity is adjusted incorrectly.
The size is incorrectly set.
- Verify that it is set to “color bag mode” mode.
Pressing the stop button doesn't bring the machine to a halt.
- The Hall sensor has been harmed
The bag magnet is in the incorrect place.
There is a problem with the temperature.
Ejectors are too low.
The timing of discharge is incorrect.
A Carding Machine for Nonwoven Fabric
Disconnection is an issue. Find out where in the carding machine, the cotton net is set out or before it is pressed that the broken net happens.
- The electronic control system malfunctions. The whole batt manufacturing process is under the electrical control of the card. Because most individuals aren't knowledgeable with electrical circuits, it's up to the manufacturer to figure out how to fix a problem.
Three. The cotton tire issue. The batt's thickness is irregular, the size is too small, and the weight is too heavy are typical issues.
Machine for making non woven machinery masks
When the non-woven mask machine's power is switched on, the ultrasonic test button does not produce any sound.
- Verify that the non-woven mask machine's emergency stop switch is pushed.
Two. The ultrasonic power transformer for the non-woven mask machine has an irregular 110- or 24-volt power supply.
The machine programming circuit board is defective.
Activate the non-woven mask machine by pressing the ultrasonic test button and turning on the power.
A gap exists between the non-woven mask machine's base and the frame's five-core wire.
There is a problem with the machine's program circuit board.
When you turn on the non-woven mask machine's power switch, nothing happens. The ultrasonic power indicator on the non-woven mask machine is dark.
There is inadequate contact between the non-woven mask machine's power cable and the power outlet.
- The non-woven mask machine's power fuse has been blown.
No ultrasonic output is produced while pushing the non-woven mask machine's ultrasonic test button and work button.
The non-woven mask machine's ultrasonic power transformer's 110V power supply is defective.
The non-woven mask machine's ultrasonic circuit motherboard's 110V power cable snapped.
0
