A product can pass in the lab because the lab applies one stress at a time, to a few clean samples, against a fixed profile and an agreed acceptance limit. That's not how the field works. During service life temperature changes, moisture, vibration, and installation differences all occur repeatedly and these stresses are additive so a pass does not mean reliability. Specialist environmental testing laboratories can close that gap, but only if each test is targeted to a failure mechanism. Three are prevalent in electronic assemblies and each requires a different test. Condensation, solder fatigue and connector fretting.
How Can a Damp Heat Test Reveal Condensation-Related Failures?
If the temperature of a surface falls below the dew point of the air around it, then condensation will take place. Not only relative humidity, but a cold heat sink in hot and humid air can also cause condensation. The layer may lead to corrosion, leakage current between adjacent tracks and defects that only show up when it is wet.
Controlled damp heat testing helps in measuring moisture entry and coating deficiencies because of its ability to hold and cycle temperature and humidity.
Not every specimen will produce condensation. There’s no single profile that is all exposure. The seals, vents, drainage and material choice all change the outcome so test the enclosure as fitted. This guide to the environmental test chamber explains how to operate the chamber.
Why Can a Thermal Cycling Test Expose Solder Fatigue?
Solder, ceramic parts, laminate, copper all expand at different rates. Every swing causes the joint to take up that mismatch as a small plastic strain, and enough repetitions will open a crack. The first sign is intermittent contact, a unit that works cold and drops out warm.
This is rarely observed since exposure to steady high temperature exerts minimal cyclic stress. This may be achieved through the use of a thermal cycling test, so long as the following criteria are met within the specified requirements of that particular method, e.g., IEC 60068 testing methods series. Passing does not mean guaranteed service life, only that the joint is resistant to that profile, which can often occur even before the joint fails completely.
How Does Vibration Testing Help Identify Connector Fretting?
Fretting is the micro-motion (sometimes a few micrometres) between mated contacts. It eats through the plating, the debris oxidises and the contact resistance rises. All three look like intermittent faults. A solder joint is broken inside the assembly. A connector is loose and has lost retention.
The vibration testing lab can replicate the movement with controlled frequency ranges, axes and severity while monitoring continuity. A rigid bench fixture can hide actual resonances. Learn about shock and vibration testing, compare the judge results to the defined acceptance criteria and choose a severity.
What Should Engineers Do Before and During Testing?
- Note the expected temperature, humidity and vibration levels before selecting a test profile.
- Check electrical performance before testing. Use these results as a baseline for comparison.
- Monitor continuity during testing when possible. Some faults appear during exposure but disappear when the unit returns to the bench.
- Take photos before and after testing. Inspect each sample for changes.
- Keep records of test conditions, failures, corrective actions and retest results in one place.
Why Choose ACE Test Labs for Environmental Testing?
While selecting an environmental testing laboratory in India, make sure its services match your testing requirements. On its environmental page, ACE Test Labs & Metrology Pvt. Ltd. has hot/cold chambers, climatic chambers and electro-dynamic vibration systems. Lab is working as per ISO/IEC 17025 and NABL accreditation is for defined scope. Verify that the test method you need is there.
BIS recognition is not equivalent to NABL accreditation. Being listed on a BIS testing company doesn’t mean environmental testing is included. Along with environmental testing, ACE also provides Electronics & IT testing services. This is useful when a product requires both types of evaluation. Before you book, please ask about sample mounting, test profiles and report details. Please confirm the temperature and humidity ranges separately as they may not be combined in one test.
Environmental Test Chamber Capability at ACE Test Labs
- Temperature range: −70°C to 180°C.
- Relative humidity range: 10% to 98% RH.
Confirm with the laboratory the test profile required, operating conditions and chamber capability prior to booking.
FAQs
- Does a damp heat pass mean condensation will never cause failure?
No. This means the sample could survive that profile and sample condition, not every real exposure, enclosure variation or installation environment.
- Are IS 9000, IEC 60068 and JSS 55555 interchangeable?
No. IS 9000 testing and JSS 55555 testing are driven by their own documents and JSS is often specified for defence work. Kindly verify the edition and method required.
- What should I confirm before booking?
The profile, whether temperature and humidity ranges can be combined, and the accreditation scope for your method.
Conclusion
These types of issues need different test methods. Engineers can improve their reliability choices by picking up the right test profiles, comparing the results with the baseline data, and analyzing failures against certain acceptance criteria. Before conducting any test, ensure that the lab is capable of performing the tests.
Author Bio
Dimpy Narang is a product testing expert associated with ACE Test Labs, focusing on product testing, laboratory services, applicable standards, and testing requirements. Readers can consult the company's NABL accredited lab information and verify the relevant scope for their testing needs.
Sign in to leave a comment.