1. The organization of fired tile glue
Clay tile cover utilizing top notch inorganic cementitious materials, fine totals, Portland cement, a limited quantity of hydrated lime and as per item quality level prerequisites added utilitarian added substance sythesis. The holding execution is fundamentally higher than the conventional cement.
Tile Adhesive is separated into two principal classes, one kind is the cement as the foundation of the dry powder items, the other is a decent blend of natural elastic items, trailed by two-section and arrangement type added substances and the hole for the caulking specialist.
Cement as the foundation of the ceramic tile glue: This sort of item from cement, fine sand, and poly in a specific extent of blended in with dry powder items.
Characteristics：
(1) on location development and blended in with water can be glued;
(2) can be utilized for indoor and open air wall floor;
(3) Great water obstruction can be utilized for long haul drenching pool, pool;
(4) just applies to the cement base and the block facade structure doesn't make a difference to the gypsum board, the board and may cause the bending, the blackout the substrate.
Natural Cement Tile Glues: These items are fundamentally acrylic items, some are PVA or elastic plastic items, to be the point:
(1) Prepared blend can be utilized;
(2) Great adaptability can be utilized for gypsum board, fiberboard, composite board, wood substrate on the top;
(3) Water opposition is marginally poor, can not be utilized for long haul drenching in the pool;
(4) Not appropriate for open air, white plastic items are not reasonable for the floor.
2. The actual properties of fired tile cement Benefits
(1) in number, serious areas of strength for attachment, keep away from the event of void drums or shedding peculiarity;
(2) The development of block wet wall can clearly further develop work productivity, helpful and quick;
(3) Great impermeability and against maturing properties;
(4) has the versatility, may assimilate the base material and the tile the extension withdrawal, successfully forestalls the earthenware tile break to create, hence extends the artistic tile administration life;
(5) with great water opposition, temperature obstruction, waterproof impermeability, freeze-defrost, cold and hot and fast degeneration, can forestall void drums and breaks. Basic activity, helpful development, high effectiveness, great water maintenance and high cement strength.
3. Kind of tile paste and application range
There are many brands of tile stick on the lookout, each brand is separated into many models, execution and cost differ. Because of clay tile makers, many, blended, item quality and cost is likewise a major contrast.
Development Innovation of tile stick
1. Tile cement flimsy Glue technique
Flimsy Glue technique is another kind of sticking fired tile innovation, with extraordinary earthenware tile cements and toothed scrubber, on the development base surface to scratch the tile folio brush into stripes, and afterward to glue the tiles on the mortar, the utilization of working and compaction of the genuine area of the dry occupation sticking strategy. Its attributes are, unit cement measurement Little, slim covering, tacky hand major areas of strength for off, affirmation, grass-roots, don't bother gurgling blocks, development speed, natural assurance.
2. Standard practice for Earthenware tile Cements
Base surface necessities
(1) Base surface ought to be level, areas of strength for perfect, residue, oil and other soil and another free;
(2) The base surface unpleasantness ought to be checked by 2 meters, the levelness is under 5mm, the verticality is not exactly the 4mm.
Development Apparatuses
Electric Stirrer (can be the 750~1000w compact electric drill, with the winding blending stick), durable plastic container, toothed scrubber, clay tile shaper, flat ruler, Cross paste granule, and so forth.
Development Innovation
(1) Projectile line situating
To decide the ground height and the plane position line, or to the wall surface to play a decent flat control line, do a base help straight.
(2) endlessly blending
For the new clump of cement mortar base surface, first, empty water into the holder, and afterward put the tile stick into the compartment, as per the standard gouache proportion to mix until the fitting consistency.
As per the extent, all together the water → added substance → tile stick into the holder, and blending simultaneously to mix to the fitting consistency. Can be mixed the hard way or precisely until the powder is free. Subsequent to blending, you really want to sit for 5 minutes, then, at that point, mix and afterward use.
(3) Scratching glue Clearing
With the tooth-molded scrubber will be covered with elastic glue and face, so the uniform dispersion, each time the figure scratching around 1 square, can be constrained by the slant point of the tooth scrubber to change the thickness of the mortar, by and large 45 degrees slant.
Use from down to top (wall request), from within to the outside or the center to the encompassing (ground request), the tile (or stone plate) work on the face can be.
The utilization of cross cards to guarantee that the upward, level, joint size consistency; the development cycle ought to be utilized to really take a look at the perfection of the flat ruler or ruler, and adapt.
Note
(1) It is completely denied to add sand, cement, and different added substances.
(2) Ceramic tile glue ought to be blended in with the utilization, blending great tile cement ought to be spent in no less than 4 hours, has set solidified mortar isn't permitted to reuse, and ought not be dry of the mortar and water blended reuse.
(3) The immovability, verticality, and levelness of the base surface ought to be affirmed before development.
(4) After the tile glue, in light of the fact that the disengagement needs change, should change inside the change time, in case influence the power.
(5) The development interaction of the additional tile paste ought to eliminated before solidify.
(6) Check the paste layer on the rear of tiles so as to guarantee that there is no vacant drum peculiarity, or it ought to be occupied in time.
(7) After the consummation of the development 24 hours, the party might step into or fill the crease.
(8) This item is appropriate for use in 5~40℃ climate.
Clay tile Glue Further developed technique
Earthenware tile standard practice, Tile stick development thickness is generally dainty, around 6mm, more than the conventional cycle to save materials, diminish costs, yet on the board surface perfection and verticality necessities, and the ongoing Division I board body Quality control impact can not completely meet the prerequisites. To guarantee the development effectiveness and development productivity, and the customary holding interaction to take on a blend of techniques, ceramic tile standard practice to improve, as follows:
1, the utilization of clay tile stick rather than cement, the tile paste and water in relation to blend, and mix to even;
2, utilize the cement digging tool to scratch the tile stick uniformly on the rear of the wall block;
3. As per the wall block line ahead of time, the tile paste will be glued on the wall, and the versatile thump is genuine;
4, the utilization of aluminum compound ruler to check, for example, verticality and evenness to meet the prerequisites of the fixed, in the event that not meet the necessities of the tiles eliminated ceramic tile paste and afterward glue.
Suggestions
Earthenware tile cement As a wall block holding material development innovation has been extremely experienced, the cycle to diminish the wall block void drum clearly assumed a decent part, and has been generally utilized in different sorts of structures. In the use of tile stick development innovation in the field project the executives, we should calmly understand, diminish, even dispose of the wall block emptying off, etc quality normal issues, the board should initially be laid out in severe consistence with a wide range of standards and lead on the premise, and in situ development endeavors to carry out the execution, yet not completely subject to the replacement of materials or innovation changes, all things considered, any improvement in the development cycle can not supplant the vital undertaking the board measures.
Sign in to leave a comment.