Latest dealsDeals See all deals→
Industrial Equipment & MachineryLogistics & Supply Chain

Push-Back Racking Explained: How It Works and When It Beats Drive-In Racking

Push-Back Racking vs Drive-In: How It Works and When to Use It

Push-back racking stores pallets very efficiently and offers faster handling and better selection than drive-in racking. If you want to increase the density of your pallet storage without slowing down your forklift operation, push-back racking may be the best solution. Several pallets are stored in each lane and loaded and unloaded from a single aisle, with gravity doing part of the work. Below we explain how the system works and when it is a better choice than drive-in racking.

How Push-Back Racking Works

As shown below, each lane in a push-back system has inclined rails with a set of wheeled carts nested on them, one fewer cart than the lane depth. The first pallet is loaded onto the top cart. Each new pallet pushes the pallets already in the lane back up the incline and sits on the next cart down, until the last pallet sits directly on the rails. To pick, the forklift removes the front pallet and the pallets behind roll forward by gravity, ready for the next pick. With push-back racking, forklifts only ever work at the front of the lane, and this is what sets it apart from drive-in racking.

Infographic: how a push-back racking lane loads and picks, a push-back vs drive-in comparison table, and when to choose push-back, drive-in or pallet flow

Push-Back vs Drive-In Racking

Drive-in racking is another high-density storage option, but forklifts must drive into the lane to place or retrieve pallets at the back. This is slower, risks collisions with the structure and puts the truck and driver inside the racking. With push-back racking, the forklift never enters the racking, so handling is faster, racking damage is reduced and product selection is greater. Because the front of every lane is always accessible, you can keep a wider range of products in different lanes. Drive-in, on the other hand, can be built much deeper, which gives it the edge on density.

Optimal Lane Depth

Push-back lanes are typically 2 to 6 pallets deep. Deeper lanes store more pallets in the same floor area but reduce the number of access points, so selection falls as depth increases. Most systems use a medium depth to balance density and product variety. Drive in racking can go deeper than push-back racking, but that is its only real density advantage.

When to Choose Push-Back Racking

If you need high density together with good pick rates and product selection, push-back racking at a medium depth is the best option for a range of products and fast handling, with no forklifts driving into the racking. It costs more to install than drive-in because of the carts and rails, but faster handling, less damage and greater flexibility can recover the investment quickly. If you need the deepest possible storage for a few high-volume products at the lowest cost per pallet, drive-in racking is the better choice. Note that both push-back and drive-in racking work on a last in, first out (LIFO) basis. If you need first in, first out (FIFO), where the oldest stock is picked first, push-back is not the right solution and pallet flow racking would be a better option.

Common Questions

How does push-back racking work?

Pallets are stored on carts that run on sloped rails in each lane, and they are loaded and unloaded from the same aisle. As each pallet enters the lane, it pushes the earlier pallets further up the slope. When the front pallet is removed, the pallets behind it roll forward by gravity. Forklifts stay in the aisle and never drive into the lane, so push-back racking is fast to work with and suffers less damage.

How deep can push-back racking be?

Push-back lanes are typically 2 to 6 pallets deep, and many systems are 4 or 5 deep. Deeper lanes store more pallets in the same space but give fewer access points and therefore less product selection. Most warehouses balance depth to get good density and selection. If you need deeper storage than push-back allows, drive-in racking can go deeper, but handling will be slower.

Is push-back racking FIFO or LIFO?

Push-back racking is last in, first out (LIFO). Pallets are loaded and picked from the front of the lane, so the last pallet in is at the front and is picked first, while the first pallet in sits at the back and is picked last. This suits stock that does not need strict expiry-date control. If you need first in, first out (FIFO), pallet flow racking is better: pallets are loaded at one end and picked from the other, so the oldest stock is always picked first.

Photo: push-back rack system being installed. U.S. Department of Defense, public domain, via Wikimedia Commons.