Things that go fast at an extremely high speed will come to a halt after a period. The same phenomenon is applicable to your high-performance Hero motorcycle that can reach its highest level of speed and must lower the acceleration whenever required.
This fluctuation of motorcycle speed highly depends on the brake's efficiency and quality. As you already know the fact that not just high capacity but mid to lower capacity motorcycles of the Hero brand also come equipped with effective disk brakes. Be it like Hero Super Splendor, Hero Passion Pro BS6, Xtec, or all variants of Glamour along with Xpulse, Xtreme 160R, and Xtreme 200S. All such offerings of the Hero Motocorp brand come equipped with dependable efficient disk brakes.
Now to keep your Hero bike's disk brakes intact and perform as per the requirement, it is relevant to follow a few maintenance tips. You need to know the important aspects of maintaining disk brakes to properly repair or at least buy new Hero spare parts online to ensure optimum riding safety.
Fill up the Brake Fluid Reservoir
You must have noticed a small oil reservoir mounted on the top of the handlebar either on the left or right side. Even check when you decide to buy Hero bike online to ensure a seamless travel experience. In terms of the brake oil reservoir, the front-wheel reservoir is on the handlebar, while the rear side is located on the left or right side heel plate attached to the footpeg.
What is important to notice is to keep checking the level of disk brake fluid or oil in the reservoir. The sight glass of both the reservoirs attached to your Hero Motocorp motorcycle allows you to check the oil level. If required, then top up the reservoir with additional fluid to maintain the seamless performance of disk brakes. Moreover, be careful not to drop a single drop of disk brake fluid on any of your bike's body parts. It is because this fluid is corrosive in nature and can damage your bike's paintwork.
Check your Brake Pads
Brake pads are the essential part of your motorcycle's disk brakes that experience an extreme level of stress and pressure. Whenever you apply the disk brakes, such pads bite on the disk rotor and experience a high level of friction along with heat. So, brake pads have to undergo a lot of pressure and abuse over a period of time.
It is imperative to timely check the brake pad's condition by inspecting the hole in the dust shield on the caliper to look at inside. This testing process will help you understand the present condition of brake pads to decide whether to replace Hero bike disk brake pads or not. Also, note the fact that using damaged disk brake pads can lead to exposed disk rotor to the metal plate and might damage the entire brake assembly. As a result of which, you will spend a hefty amount to change the entire disk braking system.
Bleed the Brakes Regularly
It's not the literal bleeding of your Hero bike's disk brakes. And not even possible to bleed the brakes. What is meant here is removing the trapped air inside the hydraulic braking system to ensure effective performance. Generally, the air is trapped inside the disk braking system as an air bubble that blocks the brake lines and makes it difficult to stop the bike on time. Thus, the air inside the brakes leads to weak performance and a serious threat to the rider's safety.
To remove air in the braking system, you have to open the bleeder screw placed on the caliper and press the brake lever. It results in pressurizing the system which further leads to leaking the air outside and fluid remaining inside the disk brake. Once the air is out, do close the bleeder screw.
Ensure Disk Rotors are Clean
This point is mainly for adventure riders who just love to take their high-performance Hero motorcycle across dirty and dusty regions. Riding in the dirt can lead to the growth of grime around the disk rotor and even in the caliper assembly. It leads to gradual stopping of the motorcycle and sometimes decreasing the braking power. As a result, you should get rid of the grime and dirt stick to the disk rotor and caliper.
For this, use the high-speed running water jet spray to ensure a thorough clean-up of the disk brake. You can even book a professional Hero motorcycle service to specifically clean the disk brakes. Although, you can clean it yourself by using Isopropyl alcohol-based solution to eliminate all the dirt, residue, and oil effectively.
Rub the Disk Brake Pads
One of the common ways to maintain the performance of a motorcycle's disk brake is cleaning the brake pads at regular intervals. Sometimes, dust and grime are attached to the pads while decreasing the braking efficiency. At such times, use sanding paper and start rubbing the brake pads to clean all the dirt and ensure optimal braking assistance. You can even do this cleaning with the help of an authorized Hero Motocorp service partner during your due bike's service and keep everything goes clean and working.
Concluding Thoughts
Brakes in your Hero Motorcycle are the most imperative components to ensure riding safety, protection, and a seamless riding experience. Disk brakes are an effective braking system to avoid slipping while applying pressure at the last minute. Therefore, maintain the efficacy of your bike's disk brakes and the overall system by referring to the above-mentioned tips. Also, in case, you need to replace the old disk brakes with new ones, then buy from the eShop Hero Motocorp platform online.
Sign in to leave a comment.