There are three main types of caning: Hand, Prewoven, and Rush caning. Listed below is an overview of the process for each. These types of caning are more difficult to repair, but if you can't figure out which one you have, the following steps should help you complete your project. So, go now to learn how to do a simple caning repair at home. Then, call a professional for a more comprehensive caning repair.
Hand caning
When your hand caning needs repair, you should seek help immediately. By seeking help as soon as you notice signs of damage, you'll reduce the amount of time and expense required to repair your hand caning. Hand caning repair is generally done by hand. Here are a few tips for your repair:
Start by removing the old cane. You can use box cutters, utility knives, or scissors to remove the old cane. Start your project with a chair that is structurally sound and the holes free of old cane. Then, measure the diameter of the holes and the center-hole distance. Use a measuring tape at several places around the seat frame, as not all holes are equally spaced. Once you know the measurements, you can begin the repair process.
To start, you should cut the cane to the desired size. Afterward, a spline is fitted to hold the cane in place. This is similar to how screen frames are installed. The spline is a long, thin piece of wood that does not extend all the way through the frame. This keeps the edges smooth and even. After this repair, you can use the chair as soon as possible. You'll be glad you took the time to repair your hand caning.
Rush and caning repairs require great skill and dedication. Rush repairs are difficult because of their intricate patterns and matchups. It takes an expert to blend the repaired areas into the rest of the piece. The process is very time-consuming, but it's well worth the effort. And remember to get a free estimate before the repair begins. You never know when something will break or need to be repaired. This way, you can rest assured you'll pay a fair price for the work.
Danny uses hole-to-hole traditional hand caning. First, he marks the center holes and weaves individual strips through them. Then, he marks two horizontal cane strands as guides, and then draws the first vertical lines across the seat. Once these lines are complete, Danny weaves the next two horizontal strands under and over the first set of strands. The horizontal strands must be parallel.
Then, you should inspect the underneath of the chair seat. A hand-caned chair will have holes drilled into the frame and strands of cane are laced through the holes. A machine-caned chair will not have holes and the cane is glued into a groove on the seat. However, this process is much easier than hand-caning. Hand-caned chairs are usually more expensive than machine-caned chairs.
Click here to read more: http://www.jardinwicker.com/
Prewoven caning
To begin repairing a cane, you must first buy new prewoven caning and a spline. The caning should be at least one to one-and-a-half inches longer than the opening it's covering, and the spline should be the proper width to fit the groove. Wet the cane and spline together for 10 to 15 minutes to soften their fibers, and then lay them over the groove shiny side up. Next, take a narrow wood wedge, such as a 1 X 2, and pound the caning until it is taut.
There are many ways to can a chair, but one of the easiest and most effective is hand caning. This type of caning is distinguished from prewoven sheet caning by its individual strands that are woven together in a pattern. Typically, the caning is manufactured using the 7 Step Method, with 2 sets of vertical strands and two sets of horizontal strands. The seventh step is a binder, and the final strands are woven into the center of the caning.
The prewoven caning is less expensive than the traditional caning, but is just as beautiful. When applied to a chair, it is akin to an elaborate version of lacing. A good quality caning system will increase the structural strength of the chair without the need for a complete replacement. Even if you're not comfortable using traditional caning, you can still repair isolated breaks in it without replacing it.
Unlike splined caning, woven caning is hand-looped. The strands of prewoven caning are looped through the holes and overlap. The pictures below show woven caning and the holes. Flat caning is then attached over the woven caning over the holes. Unlike the splined caning, woven caning is often installed under the seat or the back of the frame.
Rush caning
If your caning is showing signs of damage, you may need to seek rush caning repair. This can be done as soon as you notice the damage, which will reduce the time and cost of the repair. Many rush repair experts work by hand and can match weaving patterns to ensure a seamless repair. If you're not sure how to repair your own caning, there are several steps you can take to ensure yours looks perfect again.
To start with, rush seats are woven using the traditional technique. The material is made from dried cattail leaves. These leaves are stored in barns, where they are constantly turned over to avoid mold and facilitate even drying. After they are dried, they are soaked in water for four to six hours and then run through an old clothes ringer to remove air. After they are completely dry, one leaf is glued to one side of the chair and two or three more leaves are added throughout the weaving process.
0
0
Sign in to leave a comment.