Extender setup for MSRM US302:

Ap.Setup | MSRM US302MSRM US302 Web Browser Using a Wi-Fi Extender Setup:

• Make ensure that you have an active internet connection at home. Also, ensure that the router is linked to a power source.

• Insert the MSRM us302 extension into a power socket for a Wi-Fi router and then power it \'ON\'.

• Now, click on Wi-Fi and use your phone, laptop or some other mobile device to search for and connect to a Wi-Fi network that says \'MSRM US302\' It will, initially, have no security, no password.

• Open the browser on the same computer and then check for \'192.168.10.1\' or ap.setup / admin. You will now be redirected to a page asking for a password and an administrative username to be entered. Write \'admin\' in the \'Title\' and \'Password\' boxes, respectively.

• Click the \'Repeater Mode\' button. Now, choose the Wi-Fi network you want to extend to your current Wi-Fi router from the Wi-Fi network list.

• There are now two choices, whether to set a new name (SSID) and password, or to use the same router ID setup. Select the desired one.

• On the next tab, you will need to configure the MSRM extender networkWhen required, enter a name (SSID) and a password. You will have to do this process twice for the 2.4GHz and 5GHz networks, respectively (the password must be the same as that of the router).

To check the settings, you will be redirected to a page before you click on \'Next\'. Wait two minutes until the initialization is done for the extender to start up, and then you can connect your computers to the extender network again.

MSRM US302 setup of the Extender With WPS:

Make sure both your main Wi-Fi router and the MSRM US302 Wi-Fi range extender have a power supply connected to you. Make sure they are near enough to be located.

On the back of the Wi-Fi router, press the \'WPS\' button. For two minutes, press the \'WPS\' button on the MSRM range extender below.

The MSRM repeater can automatically link to the Wi-Fi network of your main router.

On MSRM US302: Check Firmware:

• 
  

• Make sure your extender is wired and connected to a power source by \'ON\'.

• Switch on Wi-Fi and use your phone, laptop or some other mobile device to search for and connect to a Wi-Fi network that says \'MSRM-xxx\'. It will have no encryption and no password initially.

• Open the window on the same machine, and then search for \'192.168.1.1\' http:/ap.setup/admin. You will now be redirected to a page asking for a password and an administrative username to be entered. Write \'admin\' respectively in the \'Title\' and \'Password\' dialog boxes.

• On the \'home page\', go to Administration Device Update. Click on \'Upgrade the firmware\' under the Automatic Updates tab. Make sure you have a stable internet connection to update the firmware if needed.

• Until upgraded, it could take about 2 minutes for the extender to set up and reboot.

MSRM US302 Resetting:

Press and hold the reset button on the side of the system using a pin for around 10 seconds before the extender is switched \'ON\'.

You can remember that after some time, the LED can turn red, signaling that it is rebooting.

The power LED on the extender to reboot only ensures that it is fully reset for around 30 seconds.

Methods 2:

Make sure that the Wi-Fi network of the MSRM extender is connected to either your computer, laptop or smartphone.

On the same machine, open the browser and search for AP.Setup or \'http:/192.168.10.1\'.

After entering the first page, access the administrative \'Username\' and the \'Password\'. Click on the \'Management\' option on the \'Home Page\' setup button. From the drop-down menu, click on \'System\' and then click on the \'Factory Defaults\' button.