1. Education

A Complete Guide For Xerox WorkCentre 6515 Setup

Written by Posted on Less than 0 min read
Disclaimer: This is a user generated content submitted by a member of the WriteUpCafe Community. The views and writings here reflect that of the author and not of WriteUpCafe. If you have any complaints regarding this post kindly report it to us.

Xerox WorkCentre 6515 printer is an outstanding device. It comes with a warranty of 1 year and is known for delivering a color output of exceptional quality. With sharp printing capabilities, it can save you time, money, and resources. This printer supports functions such as print, copy, email, fax, and scan, and the machine can be connected via a USB device. You can use it for official and educational purposes.

Upon purchase of this printer, you will get cartridges – 1 Cyan, 1 Magenta, and 1 Yellow. Moreover, there will be a power and fax cord, a documentation CD, and an installation guide. With a few simple steps, you can complete Xerox WorkCentre 6515 setup and quickly scan, print directly from the cloud, and scan to Email. Please note when you use genuine supplies with your printer, you will get vibrant colors, consistent output, and crisp, fine lines. Find Xerox WorkCentre 6515 ink cartridges, toners, and other supplies on the official website of Xerox.

It is essential to set up the printer carefully for smooth operations. Before you start operating your printer, here are the steps to set up this device. Connecting the printer to a wireless network from the Control Panel.

Before setting up the device, purchase the Xerox Wireless Network Interface. And then, go through the Xerox 6515 setup process steps given below.

The adapter can connect to a wireless network once the adapter has been installed and the wireless networking has been enabled and configured appropriately.

  1. As your initial step, turn off the printer..

  2. Now, please press down the latch and pull it away from the printer to remove the Wireless Network Adapter Port Cover.

  3. After that, move to the next step. Remove the Wireless Network Adapter packaging properly.

  4. Install the Wireless Network Adapter following the process as per the given instruction sheet.

Note: Once the adapter installation is complete, remove it only when needed and as directed in the removal instructions of the Wireless Network Adapter.

  1. In the next step, turn on the printer.

  2. Verify the wireless status and see the wireless IP address; move by printing a Configuration Report and examining the Connectivity Physical Connections, Connectivity Protocols, and TCP/IPv4 sections.

  3. After that, you have to click on the Home button.

  4. Now, move to Device > About > Information Pages.

  5. Once you select the Configuration Report, it will get printed.

  1. First, connect the printer to a wired network.

  2. Now, log into the Embedded Web Server as the administrator.

  3. After that, you have to click on Connectivity.

  4. Then, hit Wi-Fi in the connections area.

  5. Now, click on the toggle button to enable Wi-Fi.

  6. Next, click the Wi-Fi band and select an option.

  7. In the case of SSID, type the network’s SSID for which you want to connect.

  8. Later on, click Network Type and then choose Infrastructure or Ad hoc as required.

  1. Click Common in the TCP/IP Settings area.

  2. After that, type the printer’s DNS hostname.

  3. In step 3, click on Primary Network and select Wi-Fi.

  4. In the following step, tap the OK button.

  5. If there is a prompt, click on Restart.

  1. First, select an option, Static or DHCP mode.

  2. And then click on OK and Restart if there is a prompt.

  3. Next, configure the TCP/IP DNS Settings.

  4. After that, you need to click on DNS.

  5. Now, type the domain name for your printer.

  6. Next, input the Connection Timeout.

  7. Enable DHCP to assign the IP address.

  8. In the last step, click on OK.

  1. Proceed by disconnecting the Ethernet cable from the printer.

  2. Once the printer restarts, wait for 2 minutes.

  3. Then start printing the Configuration Report to get the IPV4 address.

When your printer isn’t working smoothly, you can go for the process of Xerox WorkCentre 6515 drivers download. It will solve the problem. Find below the manual steps to perform.

  1. Navigate to the Xerox WorkCentre 6515 software download page.

  2. Wait until the website correctly detects your printer. If it fails, select the correct version of Windows you are using.

  3. Move to step 3. Click on Apply Filter to save changes.

  4. After that, move to download the Xerox Global Print Driver.

  5. Go to the downloaded file, double-click, and follow the steps to complete the driver installation.

  6. Finally, restart your operating system to apply changes.

If you need to scan documents, photos, films, and slides on various devices, Windows, macOS, and Linux, download the Xerox Workcentre 6515 scanner driver immediately. It will make your tasks efficient.

Even though the Xerox printer is excellent for printing functions, there are times when the device runs into errors. Problems can occur with the print spooler, drivers, or printer settings in the registry. Or you can find that the device is not performing scan functions properly. Most of the issues of this printer can get resolved by detecting and restarting the device. To resolve scanning issues, ensure the drivers are installed from the website for the scanner. In case of a corrupt spooler, troubleshoot by cleaning out the print spooler and then discover if it works. If you find faults are still there, apparent from the registry.

This blog post discusses everything about the Xerox WorkCentre 6515 setup guide. The step-by-step process has been given above to help you use this printer reliably. Refer to this to set up your machine, download drivers, and troubleshoot common issues associated with this printer. We also discussed where to buy Xerox WorkCentre 6515 toner and ink cartridges.

First, go to the Control Panel and press the Home button. Now, touch the Device and Paper Trays. Click on your desired tray in the Paper Trays menu. Touch Tray Mode and then Fully Adjustable. Touch Tray Mode for a paper size, type, or color, followed by Dedicated. At last, click on the OK button to save the setting. Click on the Home button and return to the Home screen.

Xerox Workcentre 6515 can do heavy-duty printing in a micro or home office. Its duty cycle is 50,000 sheets monthly, and 3,000 sheets are the recommended page volume. You can slo use it for medium-duty printing purposes in a small office.

To find the IP address of this printer, move to the printer control panel. Press the Home button, then. Now, Touch Device > About > Information Pages. Once you find the Touch Configuration Report, see the printer’s IP address here. You can find it in the connectivity section of the IPv4 and IPv6 Configuration Report.

Source: Xerox WorkCentre 6515

Member since
Printer drivers play an important role in the functioning of printers. Printers from several brands such as HP, Canon, Brother, Epson, Rollo, and Xerox all need compatible and up-to-date printer drivers for proper functioning. So, if you have an outdated or corrupted driver, go to download printer drivers and discover perfect solutions for all driver-associated needs. Moreover, here, you can also connect with certified printer experts to discuss your concerns. They provide 24/7 help to all the printer users who are in need. So, contact them and download printer drivers. https://printerdriver.support/
Do you like printerdriver04's articles? Follow on social!

Try Our Free SEO Tools

Article Rewriter Plagiarism Checker Word Counter Fake Address Generator Random Word Generator Website Worth Calculator Password Generator